Showing 17 of 17 Engineering Resources

BPVC & B31

Codes & Regulatory

ASME Boiler & Pressure Vessel Codes

Comprehensive engineering guide to ASME Section I, V (NDE methods), VIII (Div 1 & 2 Vessels), and ASME Section IX welding qualifications.

ASME Section V mandatory NDE examination procedures

UW-51 / UW-52 Radiographic & Ultrasonic acceptance criteria

ASME Section IX WPS/PQR/WPQ essential variables matrix

ASME Sec VASME Sec VIIIASME Sec IXASME B31.3

Explore ASME Guide

API 510/570/653

Codes & Regulatory

API In-Service Inspection Standards Guide

Refinery, chemical, and pipeline inspection standards covering pressure vessels, process piping, storage tanks, and Fitness-For-Service (FFS).

API 510 Pressure vessel internal/external interval matrices

API 570 Process piping inspection classes (Class 1, 2, 3, 4)

API 579-1 / ASME FFS-1 Level 1, 2, and 3 assessment workflows

API 510API 570API 653API 579-1

Explore API Standards

AWS & ASME IX

Codes & Regulatory

Welding Standards, Flaw Atlas & PWHT

Structural steel and pressure boundary welding codes cross-referenced with AWS D1.1, ASME IX, API 1104, weld flaw morphology, and PWHT metallurgy.

AWS D1.1 Table 8.1 vs. ASME UW-51 flaw acceptance limits

10-Discontinuity Weld Flaw Morphology Atlas with NDT sensitivity

NACE MR0175 / ISO 15156 hardness limits (≤ 22 HRC) & PWHT soak times

AWS D1.1ASME IXAPI 1104NACE MR0175

Explore Welding & Flaws

B31.3 / B16.5

Codes & Regulatory

Piping Codes, Pressure Design & Hydrotest Suite

Process piping codes, P&ID line numbering, CML circuits, ASME B31.3 minimum wall thickness formula, Barlow’s hoop stress, and hydrotest rules.

ASME B31.3 §304.1.2 Internal pressure design formula breakdown

Hydrostatic (1.5×) vs. Pneumatic (1.1×) testing comparison table

ASME B16.5 Flange pressure-temperature rating table (Classes 150#–2500#)

ASME B31.3ASME B16.5API 570API 574

Open Pressure Suite

API 571 Atlas

Damage & Morphology

Types of Industrial Corrosion (API 571)

Authoritative guide to the 10 fundamental types of industrial corrosion, defect morphologies, temperature windows, and screening NDT methods.

CUI, Pitting, Flow-Accelerated Corrosion (FAC), and Stress Corrosion Cracking (SCC)

High-Temperature Hydrogen Attack (HTHA) Nelson curves per API 941

Interactive API 571 diagnostic symptom-to-sensor matrix

API RP 571API 570NACE SP0198API 941

View Corrosion Atlas

API 579 / ASME

Damage & Morphology

Mechanical Degradation & Fatigue Atlas

Mechanical, dynamic, and thermal damage atlas cataloging 10 high-consequence failure mechanisms, crack morphology, and kinetics equations.

Thermal shock crazing, vibration SBC fatigue, and creep void cavitation

Paris-Erdogan Law (da/dN) & Larson-Miller Parameter (LMP) creep math

9-Method NDT Sensitivity Matrix (PAUT, TOFD, Shear Wave, PEC, Replica)

API 571API 579-1ASME Sec VIII Div 2

View Fatigue Atlas

10 Discontinuities

Damage & Morphology

Weld Flaw Morphology Atlas

Detailed cross-sectional morphology, ultrasonic diffraction, radiography, and planar vs. volumetric sizing rules for weld defects.

Lack of sidewall fusion vs. incomplete root penetration sizing

Hydrogen-induced cold cracking (HICC) HAZ micro-fissures

PAUT -6dB drop sizing and TOFD tip diffraction time-of-flight rules

ASME UW-51AWS D1.1API 1104 Sec 9

Inspect Flaw Atlas

API Math Suite

Damage & Morphology

Asset Integrity & Remaining Useful Life (RUL)

Mathematical engineering formulas and calculation models for plant equipment corrosion rates, remaining life, and inspection intervals.

Short-term (ST) vs. Long-term (LT) corrosion rate formulas

Remaining Useful Life (RUL = [t_act - t_min] / CR) derivation

AI-assisted wall loss degradation projection models

API 510 §7API 570 §7API 653 §4

Explore RUL Models

⚡ Interactive CAD

CAD & Calculators

TEMA Exchanger Tubesheet CAD Designer

Interactive browser CAD tool for shell & tube heat exchanger tubesheet geometry, tube bundle layouts, pitch configurations, and pass partitions.

Triangular (30°), Rotated Triangular (60°), and Square (90°) tube patterns

Automatic OTLS clearance, pass lane dividers, and tie rod solvers

Live SVG rendering and CAD export for inspection scan planning

TEMA StandardsASME Sec VIII Div 1 UHX

Launch TEMA CAD

⚡ Interactive CAD

CAD & Calculators

API 653 Aboveground Storage Tank Designer

Interactive plate layout solver for API 650/653 storage tanks. Visualizes annular rings, bottom sketch plates, and critical zone inspection overlays.

Critical Zone (3" from shell) MFL and ultrasonic mapping overlay

Automatic annular plate segment count and radial projection solver

Plate cutting list and edge joint orientation optimizer

API 650API 653ASME Sec VIII

Launch Tank Designer

⚡ Interactive CAD

CAD & Calculators

Ultrasonic Scan Plan & Ray Tracing Designer

Interactive beam coverage visualizer for shear wave UT and Phased Array (PAUT). Calculate skip distance, index offset, and weld volume coverage.

V-groove, J-groove, and bevel geometry customizers

Sound beam bounce ray tracing (Half-Skip, Full-Skip, 1.5-Skip)

Probe wedge standoff, index point (X-offset), and dead zone warnings

ASME Sec V Art 4ISO 13588AWS D1.1

Launch Scan Planner

⚡ Interactive Setup

CAD & Calculators

NDT Setup Builder (UT, RT, PAUT)

Standardized calibration and inspection setup generator for ultrasonic, radiographic, and phased-array examinations.

Calibration block reference reflector specs (SDH, FBH, notches)

Radiographic geometrical unsharpness (Ug) & source-to-film solver

Exportable inspection technique sheets (SOP) with parameter logging

ASME Sec V Art 2 & 4EN ISO 17636

Open Setup Builder

Instant Solvers

CAD & Calculators

Engineering Calculators Suite

Instant solvers for pipe minimum wall thickness, pipe weight and water volume, and ultrasonic Snell’s law sound beam refraction angles.

ASME B31.3 internal pressure pipe thickness calculator

Pipe schedule dimensions (NPS 1/8" to 48", Sch 10 to XXS)

Snell’s Law critical angle solver for perspex-to-steel boundaries

ASME B31.3 §304ASME B36.10M

Open Free Calculators

Tube NDT Methods

Field Scopes & Physics

Heat Exchangers & Boilers Inspection Guide

Tubular inspection guide comparing IRIS, Eddy Current (ECT), Remote Field (RFT), and Near Field (NFT) across tube metallurgy and defect mechanisms.

Internal Rotary Inspection System (IRIS) wall loss sizing accuracy

Electromagnetic testing (ECT/RFT/NFT) screening speeds

Shell & Tube, Fin-Fan Coolers, Plate, and Condenser failure modes

TEMAASME Sec V Art 14API 510

Explore Tubing Guide

Turnaround Scopes

Field Scopes & Physics

Pre-Packaged Turnkey Inspection Scopes

Standardized scope-of-work blueprints for refinery turnarounds, tank inspections, CUI campaigns, and offshore piping programs.

Aboveground storage tank out-of-service turnaround scope

Process piping CUI screening & stripping protocol

Boiler waterwall tube inspection & UT thickness grid mapping

API 510/570/653ASNT SNT-TC-1A

View Scope Blueprints

Method Fundamentals

Field Scopes & Physics

NDT Method Physics & Calibration Guides

In-depth physics, acoustic principles, probe selection, and calibration routines for advanced non-destructive testing methodologies.

PAUT sectorial vs. linear scanning physics and encoder syncing

TOFD lateral wave, tip diffraction, and backwall echo interpretation

Pulsed Eddy Current (PEC) diffusion and footprint sizing

ASNT CP-189ISO 9712ASME Sec V

Learn Method Physics

Cross-Asset Mapping

Field Scopes & Physics

Industrial Applications & Assets Matrix

Comprehensive cross-referencing matrix mapping NDT methods directly to specific industrial assets: vessels, tanks, piping, boilers, and structures.

Upstream offshore platforms, midstream pipelines, and downstream refining

Heavy power generation, nuclear steam generators, and civil infrastructure

Optimal primary and secondary screening combinations per asset

APIASMEAWSISO

Open Asset Matrix

Ecosystem Architecture

4-Pillar Engineering Knowledge Matrix

5-Tier Platform Workflow ➔

Pillar 1

Codes & Regulatory

ASME BPVC, B31.3 piping, API 510/570/653 in-service, AWS D1.1 structural welding, and ISO 9606 welder qualifications.

Pillar 2

Damage & Degradation

API 571 Corrosion mechanisms, API 579-1 FFS fatigue and creep void cavitation, and 10 weld flaw morphologies.

Pillar 3

Interactive CAD & Tools

Browser-based TEMA tubesheet layouts, API 653 tank floor sketch solvers, and ultrasonic sound beam scan planners.

Pillar 4

Field Scopes & Physics

Turnkey turnaround inspection scopes, tube bundles (IRIS/ECT/RFT/NFT), and method physics calibration sheets.